Georgia Department of Transportation Forms

This document provides procedures for checking the straightedges used in Georgia (United States) according to the AASHTO T 99, T 134, and T 180 standards. It outlines the steps to ensure the accuracy and reliability of these tools.

This Form is used for the Annual Verification procedures of CBR Penetrating Piston AASHTO T 193 in the state of Georgia, United States.

This Form is used for checking the rate of evaporation for a drying oven. It follows the AASHTO T 104 procedure. This form is specific to Georgia in the United States.

This Form is used for checking critical dimensions of the conical mold and tamper, and calibrating pycnometers according to AASHTO T 84 procedures. It is specific to Georgia (United States).

This document provides procedures for verifying the compression strength of sulfur mortar capping in accordance with AASHTO T 106. It applies specifically to Georgia (United States).

This form is used for the verification of the physical condition of magnesium sulfate containers in Georgia, United States. It provides procedures for conducting the verification process.

This form is used for measuring the specific gravity and absorption of coarse aggregate in Georgia according to AASHTO T85 standards.

This Form is used for the calibration of Type B Pressure Meters according to AASHTO T 152 procedures in Georgia, United States.

This form provides procedures for verifying the accuracy of the Los Angeles Abrasion Machine as per AASHTO T 96 standards in Georgia.

This Form is used for verifying critical dimensions of plastic single-use molds in Georgia, United States. It follows the procedures outlined in Aashto M 205.

This form is used for verifying the critical dimensions of a concrete slump test mold according to AASHTO T 119 standards in Georgia (United States).

This form is used for calibrating volumetric air meters in the state of Georgia, United States. It provides step-by-step procedures for ensuring accurate measurements.

This form is used for the calibration of the Marshall Hand Hammer in Georgia, United States, following AASHTO T 245 procedure.

This Form is used for the calibration of the Marshall Automatic Hammer to the Hand Hammer as per AASHTO T 245 procedure in Georgia (United States).

This form is used for the checking and verification of volume change, shrinkage, and swell molds and stands in Georgia, United States.

This document describes the procedure for verifying the softening point apparatus used in AASHTO T 53 testing, specifically in the state of Georgia.

This Form is used to describe the procedure for verifying Specific Gravity Apparatus as per AASHTO T 228 in Georgia.

This document provides procedures for verifying the float test apparatus AASHTO T 50 in the state of Georgia, United States.

This Form is used for the procedure of verifying Tag Open-Cup AASHTO T 79 in the state of Georgia.

This Form is used for verifying critical dimensions and calibrating manual and mechanical rammers as per AASHTO T 99 and T 180 standards in Georgia (United States).

This document outlines the procedure for verifying the Cleveland Open-Cup AASHTO T 48 test in Georgia. It is a form used to standardize and ensure accurate testing methods.

This Form is used for verifying the Cleveland Open-Cup Apparatus in accordance with AASHTO T 48 procedure in Georgia, United States.

This form is used for verifying the critical dimensions of molds in the state of Georgia, according to AASHTO T 245 procedures.

This form is used for the verification of the recording thermometer according to ASTM C 511 procedure in the state of Georgia, United States.

This document provides the procedure for calibrating and maintaining the No. 325 sieve, which is used in testing the particle size of materials. It is specific to the state of Georgia in the United States.

This Form is used for the procedure to verify the planeness of bearing blocks according to ASTM C 109 in the state of Georgia.

This form is used for verifying the ductility test apparatus according to AASHTO T 51 standards in Georgia, United States. It outlines the procedures that must be followed to ensure accurate and reliable results.

This Form is used for the procedure of verifying the flow rate of No. 325 nozzle as per the ASTM C 430 standard in the state of Georgia in the United States.

This Form is used for the verification of flow table ASTM C 230 in Georgia.

This Form is used for the Verification of Critical Dimensions of Cube Molds according to ASTM C 109 in the state of Georgia (United States).

This Form is used for the calibration of the Blaine Fineness Apparatus as per ASTM C 204 procedure in Georgia, United States.

This Form is used for the procedure of verifying the Vicat Apparatus and Ring ASTM C187 in the state of Georgia, United States.

This Form is used for the calibration procedure of calipers used in the calibration of laboratory equipment in Georgia, United States.

This document outlines the procedure for verifying Gillmore needles according to ASTM C 266 standards in Georgia, United States.

This Form is used for the calibration of the 400 mL measure ASTM C 185 in Georgia, United States.

This form is used for verifying the Saybolt viscometer, a device used to measure the viscosity of petroleum products. It outlines the procedure for conducting the verification according to the AASHTO T 72 standard. This specific form is for use in Georgia, United States.

This type of document provides procedures for verifying the penetration test apparatus according to AASHTO T 49 standards in Georgia, United States.

This form provides procedures for verifying critical dimensions of washing vessels according to AASHTO T 210 standards in the state of Georgia, United States.

This document provides the procedure for verifying timers according to the Aashto T 72, T 201, and T 202 standards in Georgia, United States.

This type of document outlines the procedure for verifying the Autoclave ASTM C 151 in the state of Georgia, United States. It provides information on how to conduct the required verification process for the autoclave equipment.